Products - Outdoor Pedestal Mounted Emergency Eye/Face Wash Fountain with Integral Lid

Outdoor Pedestal Mounted Emergency Eye/Face Wash Fountain with Integral Lid

Outdoor Pedestal Mounted Emergency Eye/Facewash Fountain. Trace tape heated and pre-insulated. With ‘unbreakable’ integral lid, aerated diffusers, flow regulator and self-adhesive sign.
Insulated model (no heating) EXP-EJ-45G/P.
Available in Galvanised Mild Steel or Stainless Steel.
Manufactured by Hughes Safety Showers.

SKU: H-EXP-EH-45G/P
  • Specification
  • Product Information
  • Standards
  • Additional Information
Designed in accordance with ANSI and EU guidelines.
‘Unbreakable’ Wall, Table or Pedestal mounted Emergency Eye/Facewash Fountain has high flow rate aerated diffusers for improved washing action to the eyes, face and hands and incorporates an integral lid connected to the water valve for automatic operation when the lid is pulled down.
The eye wash diffusers are fitted with fine mesh strainers and a flow controller and are designed to give a gentle flow of aerated water.
Lid ensures the bowl remains clean and free from contamination.
The pipework is pre-insulated with polyurethane foam to provide maximum insulation and has a corrosion resistant polyethylene outer jacket.
Choice of optional components available including alarms and foot operation.
240V Single Phase, 50/60Hz or 110V electrical supply available.
OUTDOOR PEDESTAL MOUNTED EMERGENCY EYE/FACEWASH FOUNTAIN WITH INTEGRAL LID (EXP-EH-45G/P)
MATERIALS OF CONSTRUCTION
PIPEWORK & FITTINGS (G) Galvanised Mild Steel with 150lb medium wall tubulars and fittings
PIPEWORK & FITTINGS (GS) 316L Stainless Steel with 150lb medium wall tubulars and fittings
OPERATING VALVE Chrome Plated Brass
INSULATION & OUTER CASING Polyurethane Foam insulation with a Medium Density Polyethylene
impact resistant Outer Casing
STANDARD FINISH White with Green/White Safety Stripes (alternative colours available)
SERVICES
WATER INLET 1¼ inch Male BSP
DESIGN OPERATING PRESSURE
2.2 to 6 BAR G (Higher supply pressures can be accommodated when incorporating the optional Pressure Reducing Valve)
HEATING TYPE Trace Tape Heated (EH) or Pre-Insulated (no heating) (EJ)
HEATING LOAD 33 Watts
ELECTRICAL EQUIPMENT - Non Hazardous Suitable for use in areas classified as Non-Hazardous
ELECTRICAL EQUIPMENT - Hazardous ATEX Zone 1 & 2 Gas Groups IIA and IIB, Temp Class T3 (IIC available)
ELECTRIC SUPPLY 240V Single Phase, 50/60Hz or 110V available
TEST PRESSURE 10.3 BAR G
MINIMUM FLOW AT OPERATING PRESSURE Eye/Facewash: 20 litres/minute minimum
ENVIRONMENTAL OPERATING TEMPERATURE
MINIMUM AMBIENT OPERATING TEMP -35º C (-31º F)
MAXIMUM AMBIENT OPERATING TEMP 35º C (95º F)
ACTIVATION/OPERATION
EYE/FACEWASH OPERATION Pull lid forward to operate (Treadle foot control for hands-free - Optional)
WEIGHTS and DIMENSIONS
OVERALL DIMENSIONS 340(W) x 500(D) x 1180mm(H)
WEIGHT - UNPACKED 26Kg (No Options)
STANDARDS
ALLOCATE A LOCATION REFERENCE FOR EASE OF IDENTIFICATION.
ALL UNITS TO BE ACTIVATED WEEKLY - ANSI Z358.1 2009.
SAFETY SHOWER/EYE WASH MUST BE LOCATED WITHIN 10 SECONDS OR 15 METRES OF A POTENTIAL HAZARD - ANSI Z358.1 2009.
THE UNIT MUST BE LOCATED ON THE SAME LEVEL AS THE HAZARD AND THE PATH OF TRAVEL & LOCAL AREA SHOULD BE FREE FROM OBSTRUCTIONS - ANSI Z358.1 2009.
THE UNIT SHOULD BE WELL LIT AND IDENTIFIED WITH HIGHLY VISIBLE SIGNAGE TO BS EN ISO 7010 - ANSI Z358.1 2009.
FLUSH FOR SUFFICIENT DURATION TO PURGE THE SUPPLY PIPE WITH FRESH WATER.
REPLACE WORN OR ILLEGIBLE SAFETY SIGNS AND STICKERS.
SIGN AND DATE SERVICE TAG WHEN SERVICE COMPLETED.

This pedestal mounted insulated eyewash is designed to ensure that you meet clause 6.7(c) Australian Standard AS4775-2007. It states:

Where the possibility of freezing conditions exists, equipment shall be protected from freezing or freeze-protected equipment shall be installed.

This eyewash unit insulated and trace tape heated to prevent water from freezing in the eyewash pipes Standard Fittings

  • Integral pull-down lid to start water flow
  • High impact medium density polyethylene casing
  • Jacketed and pre-insulated tubing
  • Trace tape heated
  • Aerated diffusers
  • Flow regulator
  • Self adhesive pictogram sign

Choices

  • Hand operated or hand/foot operated

Optional Fittings

  • Treadle Foot Control (Shown)
  • Pictogram Eyewash Sign
  • Eyewash Proximity Switch

Compliance
Australian Standard AS4775-2007
US Standard ANSI Z358.1-2004

All units are supplied with complete maintenance and installation instructions.

Technical drawings are available on request.